You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close
You are viewing the article in preview mode. It is not live at the moment.

Showing articles from Qolsys tag

What are the Power Requirements for a Qolsys IQ Panel 2?

Measuring panel voltage is a common troubleshooting step when experiencing odd behavior on a panel. Most often, this step is required when there is a  Modem-Panel Comm  message, or the panel is not communicating properly with Alarm.com. If the voltage drops low, a modem-panel communication trouble may occur. Voltage…

Enable Doorbell Camera Notifications to Qolsys IQ Panel 2

Receive notifications on the Qolsys IQ Panel 2 screen when a doorbell camera detects motion or the button is pushed. Requirements To enable doorbell camera notifications to the Qolsys IQ Panel 2: Service package  A service package that supports at least one doorbell camera. Panel hardware  Firmware versio…

Adjust the Image Sensor PIR sensitivity on a Qolsys IQ Panel 2

By default, the Image Sensor is configured with a standard motion sensitivity profile  Normal . The sensor can also be set to a more sensitive motion profile (i.e.,  High ) and a less sensitive profile with pet immunity for pets up to 40 lbs (i.e.,  Low ). Adjust the PIR sensitivity Use the Partner Portal or Mobile…

Qolsys IQ Panel 2 - Battery Replacement

The Qolsys IQ Panel 2 requires a special battery pack available for purchase from the manufacturer. To replace the battery in a Qolsys IQ Panel 2: If desired, put the system in test mode with the monitoring station before proceeding. For more information, see  Put a system On Test with the monitoring station . Cau…

Interact with a Z-Wave device from a Qolsys IQ Panel 2

The Qolsys IQ Panel 2 allows users to interact with Z-Wave lights, locks, thermostats, and garage devices locally at the panel. For information about adding Z-Wave devices, see  Manage Z-Wave devices on a Qolsys IQ Panel 2 . Note : Additional Z-Wave devices may be able to be added and controlled locally. For more in…

Configure Bluetooth disarming on the Qolsys IQ Panel 2

Bluetooth Low Energy (BLE) 4.0 is built into the IQ Panel 2. The Qolsys IQ Panel 2 allows for up to five mobile Bluetooth devices to be paired with the panel. Pairing mobile Bluetooth devices allow for Bluetooth disarm, which disarms the system from an armed away state when the connected mobile device comes within ra…

What is PowerG on the Qolsys IQ Panel 2?

PowerG is a commercial-grade, two-way communications protocol with an extreme range of over 6,000 feet (about 2,000 meters), much greater than the industry standard. The signal automatically adjusts to preserve device battery life, up to eight years. The PowerG network uses Frequency Hopping Spread Spectrum technolo…

Send a Communication Test from IQ Panel 2

Sending a communication test from the panel initiates communication and verifies that the module is communicating on the cellular network. For this test to send a signal to the monitoring station, verify  Manual/Auto Tests   are selected as an  Event to Forward  in the customer's  Monitoring Settings . For more info…

Run Scenes from the Qolsys IQ Panel 2

The Qolsys IQ Panel 2 has the ability to run Alarm.com Scenes locally at the panel. For more information about configuring Scenes, see  Create/edit a Scene . Compatibility To following are required to locally run Scenes. * The Qolsys IQ Panel 2 must be on firmware version 2.4.0+. * Local Scenes support must be e…

Clear a Severe Weather Alert from a Qolsys IQ Panel 2

Severe weather alerts to the panel notify customers of incoming dangerous weather. The alerts only come in for tornado, fire, or tsunami warnings. When an alert comes in, there is a series of audible beeps and a message on the panel. For more information about severe weather alerts, see  Severe Weather Alerts . Not…

scroll to top icon