You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close
You are viewing the article in preview mode. It is not live at the moment.

Showing articles from 2GIG GoControl tag

2GIG GoControl Panic Button Remote - Installation Guide

The guides attached to this page have been written by a third party and are not maintained by Alarm.com. Any questions regarding the installation, maintenance, and/or usage instructions in these guides should be directed to the device manufacturer. To download this guide directly to your device, click  2GIG GoContr…

(Discontinued) 2GIG GoControl Wireless Smoke/Heat Alarm (2GIG-SMKT3-345) - Installation Guide

The 2GIG-SMKT3-345 is a wireless Smoke/Heat/Freeze all in one sensor. When enrolling this device to the panel, repeat the  Programming  instructions from the attached installation guide for each of the three features using a different loop number for each feature. For example, the sensor is programmed into sensor 1 …

2GIG GoControl - Battery Replacement

The 2GIG GoControl requires a special battery pack available for purchase from the manufacturer. Note : The standard backup battery that is included with all 2GIG Control Panels does not support UL 985 installations. To comply with the secondary supply requirement in  UL 985: Household Fire Warning System Units , in…

Clear a severe weather alert from a 2GIG GoControl

Severe weather alerts to the panel notify customers of incoming dangerous weather. The alerts only come in for tornado, fire, or tsunami warnings. When an alert comes in, there will be a series of audible beeps and a message on the panel. For more information on severe weather alerts, see  Severe Weather Alerts . N…

Send a communication test from a 2GIG GoControl

​Sending a communication test from the panel initiates communication and verifies that the module is communicating on the cellular network. For this test to send a signal to the monitoring station, verify  Manual/Auto Tests   are selected as an  Event to Forward  in the customer's  Monitoring Settings . F To send a…

2GIG GoControl - Sensor Groups

Each sensor (wireless or wired) installed in the system is programmed to a specific sensor number and sensor type (zone). The  sensor number  identifies the specific sensor when it is displayed on the Control Panel, recorded in the event log, or reported to the monitoring station. This allows pinpoint information ab…

Bypass a sensor on a 2GIG GoControl

On the 2GIG GoControl 1 and 2 panels, it is possible to bypass an open contact sensor, or any sensor with a trouble condition (e.g., tamper, low battery, offline, etc.) when arming a system from the Customer Website or app. When sending an arming command, the system automatically bypasses the sensor if  Q87: Keyfob/…

Verify the firmware version of a TS1 keypad and 2GIG GoControl panel are compatible

A TS1 is able to learn into a panel whether it is an older or later firmware version than the 2GIG GoControl panel, but the devices must be on the same firmware version to fully communicate properly. Currently, the only exception is firmware version 1.10, where both the panel and the TS1 need to be on version 1.10 fo…

2GIG GoControl Image Sensor ADC-IS-100-GC - Installation Guide

2GIG part number: 2GIG-IMAGE1 Alarm.com part number: ADC-IS-100-GC Product summary The Image Sensor is a pet immune PIR (passive infrared) motion detector with a built-in camera. The sensor is designed to capture images during alarm or non-alarm events. Users can also initiate image capture on-demand to  Peek-In  …

2GIG GoControl Image Sensor ADC-IS-200-GC - Installation Guide

2GIG part number: 2GIG-IMAGE1 Alarm.com part number: ADC-IS-200-GC Alarm.com Image Sensor for 2GIG GoControl Product summary The Image Sensor is a pet immune PIR (passive infrared) motion detector with a built-in camera. The sensor is designed to capture images during alarm or non-alarm events. Users can also ini…

scroll to top icon