Enable or disable motion-detected wake on an Alarm.com Smart Thermostat (ADC-T3000)
This setting will enable the Smart Thermostat (ADC-T3000) screen to wake when motion is detected nearby. Note : This feature is only available if the thermostat is AC powered. To enable or disable motion-detected wake on an Alarm.com Smart Thermostat (ADC-T3000) using the Customer Website: Note : This option doe…
Find the firmware of an Alarm.com Smart Thermostat
The firmware of an Alarm.com Smart Thermostat can be found locally on the thermostat, on the box, or on the Partner Portal. Note : To update the firmware of an Alarm.com Smart Thermostat, it must be replaced with a new one at this time. To find the firmware locally on the thermostat: ADC-T3000 * Press the butt…
Adjust the heat and cool setpoint ranges of the Smart Thermostat
To configure setpoints using the Customer Website: * Log into the Customer Website. * Click on the thermostat card. * Click the Advanced Configuration. * Using the dropdown menu, select the thermostat to configure . * In Heat Setpoint on the User tab, enter the minimum and maximum target temperatures for h…
Alarm.com Smart Thermostat (ADC-T3000) - Battery Replacement
The Alarm.com Smart Thermostat (ADC-T3000) can be powered by two AAA Alkaline batteries. Considerations: * If there are no batteries inserted, and the thermostat is running off solely of AC power, the thermostat will report a low battery (indicated by a caution sign and LOW BATTERY flashing on the display). *…
Change the temperature display on the Smart Thermostat to Celsius or Fahrenheit
The Smart Thermostat (ADC-T3000 or ADC-T2000) displays temperature based on the system's account settings set on the Customer Website. For information about changing the temperature display on the security panel, refer to each panel's Change the temperature format (units) guide. To remotely change between the Cel…
Operate the Alarm.com Smart Thermostat
The Alarm.com Smart Thermostat (ADC-T3000 and ADC-T2000) can be operated locally in addition to the remote control features on the Customer Website and app. To locally operate the ADC-T3000: Waking the device * Press any button to wake the thermostat up. Note : The ADC-T3000 display cannot stay on permane…
Alarm.com Smart Thermostat is not controlling HVAC properly
The Alarm.com Smart Thermostat may run into an issue where: * It is not turning on heat or AC. * It only controls heat or AC and not both. * Heat or AC run continuously when it should not. Note : For non-Alarm.com thermostat configuration assistance, contact the device manufacturer. If the Alarm.com Smart Ther…
Alarm.com Smart Thermostat - Wiring and Configuration Guide
For an HVAC system to be compatible with the Smart Thermostat, the system must be wired to an existing compatible thermostat. This guide assists with wiring and configuration when swapping an existing thermostat with the ADC-T3000 or ADC-T2000. Finding previous thermostat model and wiring Before replacing a therm…
Find the serial number on an Alarm.com Smart Thermostat
The serial number of an Alarm.com Smart Thermostat (ADC-T3000 or ADC-T2000) can be found on the box it came packaged in or locally on the thermostat. To find the serial number of an ADC-T3000: On the box: The serial number is the 16-digit located below the barcode on the sticker. On the thermostat: * Identi…
Enroll and configure the Alarm.com Smart Thermostat
Add or remove the Smart Thermostat To add or remove the ADC-T3000: If using a Z-Wave Security 2 (S2) and/or SmartStart-capable Z-Wave controller, see Add an S2-encrypted Z-Wave device or Add or remove a Z-Wave SmartStart-enabled device . If not, refer to the steps below: * Put the Z-Wave controller into…
