Verify the firmware version of a TS1 keypad and 2GIG GoControl panel are compatible
2GIG GoControl and TS1 Firmware Compatibility Guide A TS1 keypad can enroll into a 2GIG GoControl panel on different firmware versions, but both must be on the same firmware for full communication. The main exception is version 1.10 , where both panel and TS1 must be on 1.10 to enroll. Tip: Use the Remote Tool…
Bypass a sensor on a 2GIG GC3
On the 2GIG GC3 panel, it is possible to bypass an open contact sensor, or any sensor with a trouble condition (e.g., tamper, low battery, offline, etc.) when arming a system from the customer website or mobile app. When sending an arming command, the system automatically bypasses the sensor if Q20: Keyfob/remote a…
Bypass a sensor on a 2GIG GoControl
› 2GIG Remote Sensor Bypass 2GIG Remote Sensor Bypass & Quick Bypass Guide On 2GIG GoControl 1 and 2 panels, you can configure how the system handles open or troubled sensors when arming remotely. Using programming fields Q87 and Q72 , installers can set automatic bypass behavior and enable Quick Bypass for sched…
2GIG GC3 Image Sensor (ADC-IS-300-LP) - Installation Guide
Product summary & technical specifications The Image Sensor is a pet immune PIR (passive infrared) motion detector with a built-in camera designed to capture images during alarm or non-alarm events when motion is detected. Product features: * Communicates wirelessly to the security control panel * 35 foot de…
(Discontinued) 2GIG GC3 Image Sensor (2GIG-IMAGE2) - Installation Guide
Product overview The Image Sensor for 2GIG GC3 panels is a pet immune PIR (passive infrared) motion detector with a built-in camera. The sensor is designed to capture images during alarm or non-alarm events. Users can also initiate image capture on-demand to Peek-In on their property. Images are stored locally and …
2GIG GoControl Image Sensor ADC-IS-200-GC - Installation Guide
2GIG part number: 2GIG-IMAGE1 Alarm.com part number: ADC-IS-200-GC Alarm.com Image Sensor for 2GIG GoControl Product summary The Image Sensor is a pet immune PIR (passive infrared) motion detector with a built-in camera. The sensor is designed to capture images during alarm or non-alarm events. Users can also ini…
2GIG GoControl - Equipment Codes
Equipment Code Equipment Description Panel firmware version required 9999 Alarm.com Image Sensor Note : Must be added at the panel 1.10+ 1062 2GIG Tilt Sensor 1.19+ 1064 2GIG Bypass Sensor 1.14+ 1065 2GIG Flood Sensor 1.14+ 1066 2GIG Shock Sensor 1…
2GIG GoControl - Cellular Module Installation Guide
HowTo Schema 2GIG GoControl – Install Cellular Module & Run Cell Phone Test Pre-Install Recommendation Test in your office or lab at least 24 hours before heading to the site. This lets the SIM register on the carrier network and helps rule out module/SIM issues before you’re on-site. A successful office test conf…
(Discontinued) 2GIG Doorbell (2GIG-DBELL1-345) - Installation Guide
The guides attached to this page have been written by a third party and are not maintained by Alarm.com. Any questions regarding the installation, maintenance, and/or usage instructions in these guides should be directed to the device manufacturer. To download this guide directly to your device, click 2GIG Doorb…
2GIG GC3 - Equipment Codes
Required for all wireless zones, keyfobs, and keypads. For information on the loop number to program, refer to the device's installation manual. Wireless Zones - Equipment Codes Equipment Code Description 0000 Other 0862 2GIG Thin D/W (Surface) Contact 0863 2GIG Recessed Door Contact 0869 2GIG PIR wi…
